Guide: How to install a Processor

[Sam_Dabs]

This is a Techradar article in association with Dabs.com


What shall we compare the computer processor to this week? How about the human brain or perhaps the heart? We could go mechanical and try the car engine? In truth, there's nothing man-made that really matches the modern processor for its complexity and adaptability.

It performs billions of operations a second, running through billions of transistors. And all are packed into a silicon-based package that's no bigger than the end of your finger.

We've gone from having just one of these processors running at a few million times a second to effectively having six and soon eight processing cores packed into a single chip computing instructions at the rate of billions of times a second.

Sounds impressive? It is. And it's also not the easiest thing to upgrade the one that's currently inside your system.

Whether you're building from scratch or upgrading an existing system, it's worth reading our guide to buying a new processorand our list of the best processors around. Now let's look at how you can replace the chip inside your system.

1. Getting started



The key thing to do no matter if you're upgrading or building from scratch, is to make sure your processor matches the motherboard and memory. You can start from either end, choose a processor then pick a suitable motherboard and memory. Or more likely if you're upgrading an older system, start with the motherboard and memory you already have and match it to the best processor available.

2. Removals begin



If you're upgrading the first step is to remove the old heatsink and processor. Disconnect the fan's power cable and then start to unlock its fixing mechanism that can take many forms. Newer Intel solutions have push-down clips, usually you need to rotate these to release them. Most AMD solutions use a fixing lever to clamp the unit in place.

3. Release the CPUs



Intel uses an LGA or Land Grid Array system to hold the processor, this traps the processor against an array of delicate pins using a metal lid. Unhoock the lever beside this to flip back the CPU and carefully remove it. The AMD system uses a ZIF or Zero Insertion Force socket that traps the CPU's delicate pins in place, again use the lever beside this to unlock the socket and carefully remove the CPU.

4. Insert the CPU



When installing the CPU it's vital to install it with the correct orientation, which is to say it may be square but it can only be fitted in one position. For Intel LGA processors there are two notches cut into its sides that ensure it can only be installed one way around, line these up and drop them into place. For AMD CPUs there will be a golden triangle on one corner of the processor, this is lined up with the indented triangle on the socket.

5. Clamp it



Once you're sure the processor is seated correctly you can lock the processor into place; for Intel processors this is easier to tell as they just sit on top of the pins, for AMD processors it can sometimes be a little troublesome getting all the pins to seat but it should gently drop into the socket.

6. Heat paste



A small amount of heat paste should be applied to the top of the processor. This compound will fill in any gaps between the top of the processor and the heatsink to help keep the processor cool. For AMD processors apply a thin 1mm line horizontally above the AMD logo. For Intel processors a line going vertically up from the cap notch will do, apart from for Core 2 Quad models where the line should go horizontally parallel with the notch.

7. CPU cooler



Finally you can install the heatsink. On AMD systems this usually consists of hooking one end of a clamp in place and using a lever on the other to clamp the heatsink in place. On Intel system four fixing spots will either use screws or push-down posts to fix the heatsink in place. Connect the fan's power cable in place and you're done.

8. Fingers crossed and power on



When you power on everything should continue as normal, but it's worth diving into the BIOS to double check the processor has been detected correctly by the BIOS. Potentially, if it hasn't you may need to update the BIOS, though this shouldn't stop it from working correctly.

[Cmdrx3]

Part 5. Wow!! You need to be an intel professor now to do it, and isn't the socket a little small for a fully grown professor to sit on

[Sam_Dabs]

good spot

[elpaulio]

Just to be uber fussy, point three needs the following little typos sorted (additions in red):

Intel uses an LGA or Land Grid Array system to hold the processor, this traps the processor against an array of delicate pins using a metal lid. Unhook the lever beside this to flip back the CPU and carefully remove it. The AMD system uses a ZIF or Zero Insertion Force socket that traps the CPU's delicate pins in place, again use the lever beside this to unlock the socket and carefully remove the CPU.

Paul

[2o2o]

Think I already said this but point 6 worries me a bit not a good way to install thermal paste you will end up with uneven distribution and a lot of thermal paste spilling off the side of the processor.